SFP-DD to SFP-DD-100G-AOC-50M164FT 100G SFP-DD 2 x 50G PAM4 Active Optical Cable, 50m (164ft)

Product Highlights

• HT-manufactured AOC assembly in 50m (164ft)
• 100G connectivity at 100Gbps
• Interface configuration: SFP-DD to SFP-DD
• Fixed length and part number: 50m (164ft), SFP-DD to SFP-DD-100G-AOC-50M164FT
• Cable construction: OM4
• Maximum power consumption: ≤3.5W
• Minimum bend radius: 60mm

Specifications

Signal and Lane Configuration

The listed modulation format is 2x 50G-PAM4 to 2x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

Position Within the Length Range

SFP-DD to SFP-DD-100G-AOC-50M164FT occupies the middle of this family between SFP-DD to SFP-DD-100G-AOC-30M98FT at 30m (98ft) and SFP-DD to SFP-DD-100G-AOC-70M230FT at 70m (230ft). It adds 20m over the shorter option for extra routing clearance, while the next longer version adds another 20m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

Mixed-Vendor Network Operation

A mixed-vendor link should be documented at both ends, not treated as one generic connection. Confirm which OEM identity each host expects and whether the two ends use the same compatibility requirement. The related brand links below help locate equivalent-length assemblies, while the physical form factor and lane arrangement must still agree across the complete path. For this assembly, the minimum bend radius is 60mm; the stated power consumption is ≤3.5W.

Power and Thermal Planning

The rated power consumption is ≤3.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

Cable Construction and Routing

This assembly uses minimum bend radius 60mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Network and Protocol Considerations

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFP-DD MSA, SFP-DD MIS. Confirm that the host firmware and port configuration support the same operating mode.

Integrated Optical Assembly

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

Length Selection and Installation Planning

The extended 50m (164ft) configuration gives SFP-DD to SFP-DD-100G-AOC-50M164FT a specific place in the family reach range. It should not be treated as a universal substitute for every shorter order code. Match it to a documented route, protect the integrated optical cable and both optical engines during handling and retain the part-number label for later maintenance. Within this family, SFP-DD to SFP-DD-100G-AOC-30M98FT is shorter at 30m (98ft), while SFP-DD to SFP-DD-100G-AOC-70M230FT is the next longer choice at 70m (230ft); comparing those two boundaries helps avoid both tension and unnecessary slack.

Generic Compatibility and Factory Testing

Testing addresses the brand-specific identification as well as the operating link and available diagnostics. The same physical cable family can require a different host identity for another equipment vendor, so the intended platform should be supplied when a deployment combines multiple brands or unusual hardware revisions. Where supported by the host, receive activity and diagnostic indications are reviewed together with the established link.

Ordering Information

For mixed-vendor projects, identify the equipment at both ends along with the OEM reference, length and quantity. Order each compatibility version under its own part number. If spare assemblies are required, list them separately so labels and test records remain unambiguous. Keep SFP-DD to SFP-DD-100G-AOC-50M164FT associated with 50m (164ft) throughout the order and receiving record.

Quality Assurance and Packaging

Both ends are inspected and the complete assembly is powered up for a functional check before packing. Connectors are protected individually and the cable is secured without tight bends. Optional labels can distinguish host brand, OEM reference and length for easier spares management. Volume orders can include customer references on the labels and carton list.

Frequently Asked Questions

Shipping and Lead Time

Standard configurations normally ship within one to three working days, while production quantities are confirmed with the order. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.