Cisco QDD-2X400G-FR4 Compatible 800G QSFP-DD Transceiver Module
This Cisco QDD-2X400G-FR4 compatible transceiver provides 800G connectivity in a hot-swappable QSFP-DD package. Its optical design operates at 1271nm, 1291nm, 1311nm and 1331nm for up to 2km, using Dual Duplex LC/UPC. Complete parameters and related OEM references help mixed-vendor networks document the correct compatibility identity at each host.
OEM Part Number: QDD-2X400G-FR4HT Part Number: QDD-2FR4-800G
Product Highlights
- Compatible alternative to Cisco QDD-2X400G-FR4
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 1271nm, 1291nm, 1311nm and 1331nm
- Specified reach: 2km
- Dual Duplex LC/UPC / SMF interface
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Cisco Compatible | QDD-2X400G-FR4 |
|---|---|
| Manufacturer | HT |
| HT Part Number | QDD-2FR4-800G |
| Form Factor | QSFP-DD |
| Max Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 1271nm, 1291nm, 1311nm and 1331nm |
| Max Cable Distance | 2km |
| Connector | Dual Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| TX Power | -3.2~4.4dBm |
| Minimum Receiver Power | -7.2dBm |
| Power Budget | 4dB |
| Receiver Overload | 4.4dBm |
| Max Power Consumption | 17W |
| Extinction Ratio | ≥3.5dB |
| Modulation (Electrical) | 8x100G-PAM4 |
| Modulation (Optical) | 8x100G-PAM4 |
| Packaging Technology | COB (Chip on Board) Packaging |
| CDR (Clock and Data Recovery) | TX and RX Built-in DSP |
| Inbuilt FEC | No |
| Protocols | IEEE 802.3cu-2021, IEEE 802.3ck-2022, QSFP-DD MSA HW Rev 6.01, CMIS Rev 5.0 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 2km. Inspect every Dual Duplex LC/UPC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3.2~4.4dBm; the stated optical power budget is 4dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Mixed-Vendor Network Operation
A mixed-vendor optical link should be documented at both ends, not treated as one generic connection. Confirm which OEM identity each host expects and whether both ends use the same wavelength plan and optical standard. Related links locate equivalent hardware, but brand-specific identification must still be selected independently. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 1271nm, 1291nm, 1311nm and 1331nm, rated reach 2km.
Cisco Compatibility and Factory Testing
Compatibility testing for QDD-2X400G-FR4 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
When ordering, specify QDD-2X400G-FR4, QDD-2FR4-800G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Each QDD-2X400G-FR4 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QDD-2X400G-FR4, not an original Cisco-branded module.
Which fiber and connector are required?
Use Dual Duplex LC/UPC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Transceivers
Malaysia Fiber Optic Supplier
Malaysia Fiber OpticsFactory Address: Block 5, Wangtang Industrial Park,Nanshan Area, Shenzhen,China
Malaysia Office: 68000 Ampang,
Selangor, MYhttps://www.fiberoptic.com.my