Cisco OSFP800-XDR8-B2 Compatible 800G Twin-port OSFP IHS/Closed Finned Top Transceiver Module
The OSFP800-XDR8-B2 compatible module serves equipment requiring a 800G Twin-port OSFP IHS/Closed Finned Top interface with 1310nm optics and a 2km rating. Connection is through Dual MPO-12/APC. Product data, application guidance and factory verification are presented together to support mixed-vendor networks document the correct compatibility identity at each host.
OEM Part Number: OSFP800-XDR8-B2HT Part Number: OSFP800-XDR8-B2
Product Highlights
- Compatible alternative to Cisco OSFP800-XDR8-B2
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 1310nm
- Specified reach: 2km
- Dual MPO-12/APC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | OSFP800-XDR8-B2 |
|---|---|
| Manufacturer | HT |
| Form Factor | Twin-port OSFP IHS/Closed Finned Top |
| Max Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 1310nm |
| Max Cable Distance | 2km |
| Connector | Dual MPO-12/APC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | Siphotonics PIN |
| TX Power | -3.1~4dBm |
| Minimum Receiver Power | -7.1dBm |
| Power Budget | 4dB |
| Receiver Overload | 4dBm |
| Max Power Consumption | 16.5W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x100G-PAM4 |
| Modulation (Optical) | Dual 4x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX and RX Built-in DSP |
| Packaging Technology | COB (Chip on Board) Packaging |
| Bit Error Ratio (BER) | 2.4E-4 |
| MTBF | 3,222,983 Hours (@40°C, 60% CL)1,632,641 Hours (@40°C, 90% CL) |
| Protocols | IEEE 802.3ck, IEEE 802.3cu-2021, OSFP MSA, CMIS Rev 5.0 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a Twin-port OSFP IHS/Closed Finned Top housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 2km. Inspect every Dual MPO-12/APC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3.1~4dBm; the stated optical power budget is 4dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Mixed-Vendor Network Operation
A mixed-vendor optical link should be documented at both ends, not treated as one generic connection. Confirm which OEM identity each host expects and whether both ends use the same wavelength plan and optical standard. Related links locate equivalent hardware, but brand-specific identification must still be selected independently. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 1310nm, rated reach 2km.
Cisco Compatibility and Factory Testing
The module is checked for host recognition as OSFP800-XDR8-B2, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Use OSFP800-XDR8-B2 as the compatibility cross-reference and OSFP800-XDR8-B2 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies OSFP800-XDR8-B2, not an original Cisco-branded module.
Which fiber and connector are required?
Use Dual MPO-12/APC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Transceivers
Malaysia Fiber Optic Supplier
Malaysia Fiber OpticsFactory Address: Block 5, Wangtang Industrial Park,Nanshan Area, Shenzhen,China
Malaysia Office: 68000 Ampang,
Selangor, MYhttps://www.fiberoptic.com.my