Intel SPTSBP4LLCDF Compatible 100G QSFP28 LR4 Transceiver Module
Built for hosts recognizing SPTSBP4LLCDF, this HT-manufactured QSFP28 module delivers 100G transmission at 1310nm. Its rated reach is 10km, with Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support mixed-vendor networks document the correct compatibility identity at each host, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SPTSBP4LLCDFHT Part Number: QSFP-LR4-100G
Product Highlights
- Compatible alternative to Intel SPTSBP4LLCDF
- 100G connectivity at 103.125Gbps (4x 25.78Gbps)
- Optical wavelength: 1310nm
- Specified reach: 10km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Intel Compatible | SPTSBP4LLCDF |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-LR4-100G |
| Form Factor | QSFP28 |
| Max. Data Rate | 103.125Gbps (4x 25.78Gbps) |
| Wavelength | 1310nm |
| Max. Cable Distance | 10km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | 4 x LAN WDM EML |
| Receiver Type | PIN |
| TX Power | -4.3~4.5dBm |
| Minimum Receiver Power | -10.6dBm |
| Power Budget | 6.3dB |
| Receiver Overload | 4.5dBm |
| Max. Power Consumption | 3.5W |
| Extinction Ratio | >4dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Packaging Technology | BOX Packaging |
| MTBF | 8,340,283 Hours |
| Bit Error Ratio (BER) | 1E-12 |
| Protocols | QSFP28 MSA, SFF-8636, IEEE 802.3‑2012, PSM4 MSA, CAUI-4 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 10km. Inspect every Duplex LC/UPC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.3~4.5dBm; the stated optical power budget is 6.3dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Mixed-Vendor Network Operation
A mixed-vendor optical link should be documented at both ends, not treated as one generic connection. Confirm which OEM identity each host expects and whether both ends use the same wavelength plan and optical standard. Related links locate equivalent hardware, but brand-specific identification must still be selected independently. For this model, the principal parameters are data rate 103.125Gbps (4x 25.78Gbps), wavelength 1310nm, rated reach 10km.
Intel Compatibility and Factory Testing
Compatibility testing for SPTSBP4LLCDF combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
When ordering, specify SPTSBP4LLCDF, QSFP-LR4-100G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Each SPTSBP4LLCDF compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Intel transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SPTSBP4LLCDF, not an original Intel-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Transceivers
Malaysia Fiber Optic Supplier
Malaysia Fiber OpticsFactory Address: Block 5, Wangtang Industrial Park,Nanshan Area, Shenzhen,China
Malaysia Office: 68000 Ampang,
Selangor, MYhttps://www.fiberoptic.com.my