SFP-DD to QSFP28-100G-AOC-7M23FT 100G SFP-DD 2 x 50G PAM4 to QSFP28 4 x 25G NRZ Active Optical Cable, 7m (23ft)

Product Highlights

• HT-manufactured AOC assembly in 7m (23ft)
• 100G connectivity at 100Gbps
• Interface configuration: SFP-DD to QSFP28
• Fixed length and part number: 7m (23ft), SFP-DD to QSFP28-100G-AOC-7M23FT
• Cable construction: OM3
• Maximum power consumption: SFP-DD: <3.5WQSFP28: <5.5W
• Minimum bend radius: 30mm

Specifications

Signal and Lane Configuration

The listed modulation format is SFP-DD-2x 50G-PAM4 QSFP28-4x 25G-NRZ. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

Integrated Optical Assembly

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

Length Selection and Installation Planning

At 7m (23ft), SFP-DD to QSFP28-100G-AOC-7M23FT should be planned as an extended equipment-room connection rather than a short in-rack jumper. Mark the complete vertical and horizontal route before installation, including every manager the cable will actually pass through. Support the integrated optical cable and both optical engines along that path and keep both ends free from pull loads. Within this family, SFP-DD to QSFP28-100G-AOC-5M16FT is shorter at 5m (16ft), while SFP-DD to QSFP28-100G-AOC-10M33FT is the next longer choice at 10m(33ft); comparing those two boundaries helps avoid both tension and unnecessary slack.

Position Within the Length Range

SFP-DD to QSFP28-100G-AOC-7M23FT occupies the middle of this family between SFP-DD to QSFP28-100G-AOC-5M16FT at 5m (16ft) and SFP-DD to QSFP28-100G-AOC-10M33FT at 10m(33ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 3m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

Mixed-Vendor Network Operation

A mixed-vendor link should be documented at both ends, not treated as one generic connection. Confirm which OEM identity each host expects and whether the two ends use the same compatibility requirement. The related brand links below help locate equivalent-length assemblies, while the physical form factor and lane arrangement must still agree across the complete path. For this assembly, the minimum bend radius is 30mm; the stated power consumption is SFP-DD: <3.5WQSFP28: <5.5W; the jacket material is OFNP.

Power and Thermal Planning

The rated power consumption is SFP-DD: <3.5WQSFP28: <5.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

Cable Construction and Routing

This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Network and Protocol Considerations

The intended application is 100GBASE SR2 Ethernet. Listed interface and protocol references include SFP-DD & QSFP28 MSA, IEEE 802.3cd, RoHS6 (Lead-free). Confirm that the host firmware and port configuration support the same operating mode.

Generic Compatibility and Factory Testing

Testing addresses the brand-specific identification as well as the operating link and available diagnostics. The same physical cable family can require a different host identity for another equipment vendor, so the intended platform should be supplied when a deployment combines multiple brands or unusual hardware revisions. Where supported by the host, receive activity and diagnostic indications are reviewed together with the established link.

Ordering Information

For mixed-vendor projects, identify the equipment at both ends along with the OEM reference, length and quantity. Order each compatibility version under its own part number. If spare assemblies are required, list them separately so labels and test records remain unambiguous. Keep SFP-DD to QSFP28-100G-AOC-7M23FT associated with 7m (23ft) throughout the order and receiving record.

Quality Assurance and Packaging

Both ends are inspected and the complete assembly is powered up for a functional check before packing. Connectors are protected individually and the cable is secured without tight bends. Optional labels can distinguish host brand, OEM reference and length for easier spares management. Standard protective packing is used by default, with project documentation arranged when requested.

Frequently Asked Questions

Shipping and Lead Time

Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Worldwide courier services are available, with air or sea freight for consolidated shipments; freight-collect delivery and coordination with a customer’s logistics provider can be arranged.