Ciena 180-3360-900 Compatible 400G QSFP-DD Transceiver Module

Product Highlights

• Compatible alternative to Ciena 180-3360-900
• 400G connectivity at 100G-31.5Gbaud（OTN STD） 200G-31.5Gbaud（OTN STD） 200G-63 Gbaud（OTN STD） 400G-63 Gbaud（OTN STD） 400G ZR 400G ZR+
• Optical wavelength: 1528.58-1567.54nm
• Specified reach: 400G ZR：120km 400G ZR+：1000km 100G-31.5Gbaud（OTN STD）：3300km 200G-31.5Gbaud（OTN STD）：800km 200G-63 Gbaud（OTN STD）：3000km 400G-63 Gbaud（OTN STD）：1300km
• Duplex LC/UPC / SMF interface
• Digital diagnostic monitoring: Support
• Operating temperature: 0℃ to 75°C

Specifications

Applications and Optical Link Design

This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.

Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.

Coherent deployment requires a line-system review, not merely a matching connector. Confirm the DWDM channel, launch-power range, receiver limits, OSNR and FEC mode at both ends. Span loss and amplifier operation must remain inside the supported envelope, and stated reach should be validated against the actual route.

Optical Acceptance, Diagnostics and Handling

Use the electrical and optical limits in the specification table as the acceptance reference for this model. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Support. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.

Mixed-Vendor Network Operation

A mixed-vendor optical link should be documented at both ends, not treated as one generic connection. Confirm which OEM identity each host expects and whether both ends use the same wavelength plan and optical standard. Related links locate equivalent hardware, but brand-specific identification must still be selected independently. For this model, the principal parameters are data rate 100G-31.5Gbaud（OTN STD） 200G-31.5Gbaud（OTN STD） 200G-63 Gbaud（OTN STD） 400G-63 Gbaud（OTN STD） 400G ZR 400G ZR+, wavelength 1528.58-1567.54nm, rated reach 400G ZR：120km 400G ZR+：1000km 100G-31.5Gbaud（OTN STD）：3300km 200G-31.5Gbaud（OTN STD）：800km 200G-63 Gbaud（OTN STD）：3000km 400G-63 Gbaud（OTN STD）：1300km.

Ciena Compatibility and Factory Testing

Compatibility testing for 180-3360-900 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.

Ordering Information

When ordering, specify 180-3360-900, QDD-ZRPH-400GM, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.

Quality Assurance and Packaging

Each 180-3360-900 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.

Frequently Asked Questions

Shipping and Lead Time

Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.